· Crystalline Technology
· Product Range

The Xypex line of crystalline, concrete waterproofing products have been developed to meet the wide variety of application situations faced by industrial users. Xypex can be applied as an admix, as a slurry coat, or by the dry shake method.

ADMIX C-1000NF
With the Admix C-Series, Xypex's unique crystalline dry powder compound for the waterproofing, protection and improvement of concrete is added to the concrete mix at time of batching. Admix C-1000NF has been formulated to meet specific project and temperature conditions.

ADMIX C-1000NF   Data Sheet »   M.S.D.S. »

ADMIX C-5000
Admix C-5000 is a unique chemical treatment that has been specially formulated to enhance the durability of reinforced concrete exposed to aggressive conditions. It is recommended for reinforced concrete including pre-cast, pre-stressed, post-tensioned and shotcrete and is applied at time of batching. Admix C-5000 complies with the requirements of AS 1478.1 as a type SN Special Purpose Admixture.

ADMIX C-5000  Data Sheet »   M.S.D.S. »

XYPEX CONCENTRATE DS-1 and DS-2
DS-1 and DS-2 are special dry shake formulations of Xypex Concentrate designed specifically for horizontal concrete surfaces such as parking decks and floor slabs. Applied by hand or by mechanical spreader, DS-1 and DS-2 are trowelled into fresh concrete prior to finishing. DS-2 is used for concrete structures where increased abrasion resistance is required.

XYPEX CONCENTRATE DS-1   Data Sheet »   M.S.D.S. »
XYPEX CONCENTRATE DS-2   Data Sheet »   M.S.D.S. »

XYPEX CONCENTRATE
Xypex Concentrate is the most chemically active of the Xypex waterproofing products. When mixed with water, this light grey powder is applied as a slurry coat to above-grade or below-grade concrete either as a single coat or as the first of a two-coat application. It is also mixed in Dry-Pac form for sealing strips at construction joints, or for the repairing of cracks, faulty construction joints and honeycombs.

XYPEX MODIFIED
Xypex Modified can be applied as a second coat to reinforce Xypex Concentrate or by itself to damp-proof the exterior of foundation walls. Applied as a second coat over Concentrate, Modified produces a harder finish and speeds the curing of the Concentrate. Where damp-proofing is required, a single coat of Modified may be used as an alternative to a spray/tar emulsion.

XYPEX MEGAMIX I
This product can be applied as a thin parge coat - up to 10mm thick to waterproof and protect masonry and deteriorated concrete surfaces. With excellent bond strength and resistance to aggressive environments this product is suitable for relining swimming pools, tanks, tunnels and other deteriorated concrete surfaces.

Data Sheet »   M.S.D.S. »

XYPEX MEGAMIX II
Is a one component, high build repair mortar, which is enhanced with Xypex's unique crystalline waterproofing and chemical protection technology. This product can be applied to a thickness of 50mm in a single application and is suitable for repairing deteriorated concrete in marine and sewage environments.

Data Sheet »   M.S.D.S. »

XYPEX PATCH 'N PLUG
Xypex Patch'n Plug is formulated as a crystalline, fast-setting, non-shrink, high-bond-strength, hydraulic cement compound for concrete repairs. It stops flowing water in seconds and is used to seal cracks, fill tie-holes and other defects in concrete.

XYPEX RESTORA-TOP
Xypex Restora-Top products are designed specifically for the repair and rehabilitation of horizontal concrete surfaces such as warehouse floors, bridge decks, roads, curbs, and walkways where the repaired area must be returned to normal service within two hours of the completed repair. Restora-Top products consist of specially modified portland cement, aggregates, admixtures and bonding agents combined in controlled proportions to provide excellent adhesion properties, rapid setting and strength gain, as well as superior durability and reduced shrinkage.
 

XYPEX RESTORA-TOP 200   Data Sheet »   M.S.D.S. »
XYPEX RESTORA-TOP 100   Data Sheet »   M.S.D.S. »
XYPEX RESTORA-TOP 50   Data Sheet »   M.S.D.S. »

XYPEX FCM
Xypex FCM is specially designed for repaiting cracks subject to movement, sealing construction joints, restoring deteriorated concrete and waterproofing concrete structures. FCM has exceptional adhesive and elongation characteristics and is often used in conjunction with the Xypex Crystalline Concrete Waterproofing and Protection System. FCM is a two component product consisting of a specialized liquid polymer dispertion and a cementitious powder component. These ingredients are mixed just prior to application.

M P&P Mortar
M P&P Mortar is a fast-setting, non-shrink mortar for concrete repairs where waterproofing is a requirement. It is used to sealing cracks to stop water flows and other defects in concrete. M P&P Mortar is also used to seal tie-holes.

XYPEX GAMMA CURE
Xypex Gamma Cure is a curing agent designed specifically for Xypex crystalline waterproofing products. The use of Gamma Cure may eliminate the need for water curing the Xypex coating in some cases. Consult manufacturer for specific recommendation.

XYCRYLIC ADMIX
Xycrylic Admix is a water-based polymer dispersion specifically designed for fortifying portland cement compositions. The liquid is milky-white in colour and has a solids content of 40%. Xycrylic-Admix can be used with Xypex Patch'n Plug to increase bond strength.

Xypex Quickset
Quick Set us a water-soluble liquid blend of silicates, neutralizers and penetrating agents specially compounded to harden, dustproof and seal the surfaces of fresh or newly cured concrete floors.

KUNISEAL C-31
Kuniseal C-31 has been developed as an easy to use Bentonite/Clay concrete waterstop material. Used in construction joints, it reduces installation time and has the ability to swell on contact with water and fill any voided area in the surrounding concrete, eliminating the passage of water. The Kuniseal expansion does not exert pressure on the surrounding concrete.

KUNISEAL TAPE TP-50
Kuniseal Tape TP-50 is a composite product consisting of cloth covered in a Bentonite/Mineral Oil solution, which is specifically designed as a water barrier where water has made contact on any of it's surfaces. Expansion potential is approximately 2 times. TP-50 will expand to fill voids where water has penetrated.

Restec Silica Fume
Restec Silica Fume is sourced from reliable suppliers who deliver quality and readily available material.

The product is available in 10kg degradable bags, bulk bags and bulk for silo use. Continuous testing is conducted on the materials to ensure the end user is receiving a quality product at all times.

Restec Silica Fume supplies both Densified and Undensified Silica Fume to the market and product is available in all states. For further information and product supply, please contact Maria Bobeldyk 0447 290 896.

The Restec Silica Fume Datasheet and MSDS can be downloaded from www.restecsilicafume.com